Home >

Requirements And Standards For Cutting Of Clothing Tailoring Workshop

2010/4/30 9:31:00 40

한국어 日本語 Français English 中文

Tailoring

1. Styles: jacket

Fabric categories: woollen, woollen, knitted, fabric cutting requirements and error criteria are as follows:

1. the tolerance of the front and rear pieces (length of garment, flap length and side seam length) is + 0.3 cm.

2. the width error of the front and rear films (chest circumference and swing) is allowed to be + 0.3 cm.

3. the tolerance of the collar collar is + 0.2 cm.

The 4. large and small sleeves (inner length, outer length) have a tolerance of + 0.3cm.

5. the size of sleeve sleeves (sleeve width, width of cuff) error is allowed to + 0.2cm.

6. in the same cloth, front, back, and size of the same piece of cloth.

But the slope of the hem should not exceed 1.5 cm.

Two. Compound, coating, leather, chamois leather. The cutting error standards are as follows.

1. the length error of the front and rear film (the length of the garment, the length of the flap and the length of the side seam) is allowed to be + 0.2cm.

2. the width error of the front and rear films (chest circumference and swing circumference) is two to 0.2 cm.

3. the collar error is allowed to be + 0.2 cm.

4. the size and width of the sleeves (inner length and outer length) are allowed to be + 0.2cm..

5. the size of sleeve sleeves (sleeve width, width of cuff) allows an error of + 0.15cm.

6. inch cloth, front and back piece, big and small sleeves, length and width error is not allowed to + 0.3 cm.

But the slope of the hem should not exceed + 0.15cm.

Medium length, windbreaker and cotton jacket: fabric is similar to jacket fabric.

Three, cashmere, woolen and knitted fabrics

1. front and rear films (length of garment, flap length and side seam length) are three long, with tolerance of + 0.4 cm.

2. the width error of the front and rear films (chest circumference and swing circumference) is two to 0.2 cm.

3. the collar error is allowed to be + 0.15 cm (size).

4. the size and width of the sleeves (inner length and outer length) are allowed to be + 0.2cm.

5. the size and width of the sleeves (sleeves and cuffs) is 0.15cm.

6. inside cloth, front and back, big and small sleeves with same cloth request.

But the slope of the hem should not exceed + 0.15cm.

Four. Composite, coating, leather, suede.

1. the length error of the front and rear pieces (length of garment, flap length and side seam length) should not exceed 0.1 cm.

2. the width of the circumference of the front and rear pieces (chest circumference and swing) should not exceed two cm 0.2.

3. the size error of collar collar is allowed to be + 0.15 cm.

4. the size and width of the sleeves (inner length and outer length) are allowed to be + 0.15cm.

5. size and sleeve size (sleeve size, cuff size) do not allow errors.

6. Li cloth, front and back piece, big and small sleeves, length and width error should not exceed 0.3 cm.

The slope of the thread is not more than 0.15cm.

After the press is changed, the main slice and accessory piece of all kinds of fabrics must be no more than 0.1 cm.

After the forming of the stripes and frames, the error of the left and right pieces can not exceed 0.1 cm, especially the stripes.

If you have corduroy, worsted, pure cotton, linen, silk spinning, silk, and so on, all the main and auxiliary pieces will be

Length and width do not allow errors.

The above content refers to the standard of the cutting error.

It is hoped that in practice, we should not exceed this standard, we must be meticulous and quality first.

If the above error is found during the inspection of the workshop, the workshop will arrange the film and handle it on its own.